119,00

SpeedUp GHOST is an electronic and intelligent speed release device that does not need any external power supply.

It is designed for Shimano Steps E6002, E6100, E7000, E8000 and E8080 engines, also with DI2 electronic gearbox, to circumvent the 25 kmH speed lock allowing to increase the active assistance up to unlimited speed by fully exploiting the potential of the excellent engine.

Vedi di più...
Clear

SKU N/A Category


Share

WARNING!

All SpeedUp devices for Shimano are compatible with the firmware released before 05/22/2019.
Do not upgrade with later versions otherwise the device will not work.

What is SpeedUp Ghost?

SpeedUp GHOST is an electronic and intelligent speed release device that does not need any external power supply.

It is designed for Shimano Steps E6002, E6100, E7000E8000 and E8080 engines, also with DI2 electronic gearbox, to circumvent the 25 kmH speed lock allowing to increase the active assistance up to unlimited speed by fully exploiting the potential of the excellent engine.

Speedup GHOST is very simple to assemble thanks to the connectors compatible with the original Shimano ones, which do not require any physical modification to the ebike. It does not modify in any way the electronics of the Shimano engine that can be restored at any time and in a few minutes by disconnecting the device.
This allows the warranty and the actual commercial value of the bicycle to remain unchanged.

The GHOST rear wheel avoidance operating system only starts when the expected threshold of about 23KmH is reached * reducing the communication of the wheel revolutions to the engine according to the precise Frozen algorithm without the cyclist feeling any difference in the support. It does not intervene in any way at low speeds. This is an important feature designed to not vary the intervention parameters of the motor at the restart and in the important and very slow climbs (which are the critical and most delicate moments for an engine) thus leaving intact the parameters studied and optimized by the manufacturer, and thus avoiding power losses, failures or “hiccups” operations.

SpeedUp GHOST is available in one version only:

– Version on / off lights with connectors: the device is equipped with connectors compatible with Shimano ones (no wire cutting is necessary). It is perfectly compatible with the DI2 electronic gearbox.
It can be activated / deactivated by the ebike light control; with the “lights on” command the device will be active and with the “lights off” command the device will be deactivated and the ebike will work exactly as if no device were fitted.
If the ebike does not mount lights powered by the battery of the Shimano system it is almost always necessary to activate the engine lights output (once and for all) to allow the device on / off operation.
– The SC-E8000 display allows the activation of the Lights output by connecting via bluetooth and the Shimano E-Tube application (available on Playstore) or with the Shimano SM-PCE1 interface normally in possession of Shimano dealers.
– The SC-E6010 display (with physical key only for the lights) allows the activation of the light output only with the Shimano SM-PCE1 interface normally in possession of Shimano dealers.
– The SC-E6000 display (whose light control is on the corresponding handlebar control) allows the activation of the light output only with the Shimano SM-PCE1 interface normally in possession of Shimano dealers.

SpeedUp GHOST will work, once installed, with the algorithm called Frozen:

Frozen mode (designed for DI2): from 0 to 22 KmH approx. * Real the display will show the real speed, while from 22 KmH around * real up to unlimited speed will show the blocked speed on 22 KmH approx *

* The variable is linked to the circumference of the wheel, the default value entered in the device is 2250mm; the 22KmH threshold will therefore be accurate only with wheels of this circumference

Ebike software compatible with furious

The operation of the Ghost devices is guaranteed for the software versions of the ebikes released up to the date of purchase of Ghost.
If the ebike is subsequently updated with software for which the Ghost device has not been tested you may experience the failure of the same. Before updating your engine it is advisable to check the compatibility with your Ghost device.

 

What device does it do for me?

Click here for a comparison table of our Shimano release systems

 

 

The main features

– Totally INVISIBLE

– It can be assembled / disassembled at any time without leaving any trace

– Equipped with CONNECTORS it does not need any modification to the original parts of the bicycle

– The engine will assist up to unlimited maximum speed

– Installed in a few minutes

– Suitable for Shimano Steps E6002, E6100, E7000E8000 ed E8080 engines mounted by many homes

– Does not need external batteries or power supply.

 

 

 

Video Installation Instructions

The following video illustrates the steps to mount your FURIOUS device. The procedure is the same for GHOST.

SpeedUp GHOST on/off luci per Shimano E8000 con connettori

 

How to activate the light output on ebike Shimano with the E-Tube Project Shimano app


This site uses cookies to enhance your experience. By continuing to the site you accept their use. More info in our cookies policy.     ACCEPT

ATTENTION, IMPORTANT NOTICE
Once the SpeedUp speed release device has been installed, the electric bicycle, being over the limit of 25 kmH, is equated to a moped and as such, if it circulates in public places, requires the homologation-registration by the Civil Motorization, it is subject to payment of road tax and insurance coverage, must have a license plate, cannot travel on cycle paths and the driver is obliged to drive with a license and must wear a helmet. Furthermore, driving a motor bike equivalent to a moped that does not comply with the aforementioned provisions involves the administrative seizure of the vehicle and fines that vary according to the infringement committed.
The manufacturer of the speed release system accepts no responsibility for any damage caused to the pedal assisted bicycles on which the device is mounted as well as to direct or indirect damage to people or things.
Please note that changing the bicycle invalidates the manufacturer’s warranty.

EBIKE SOFTWARE COMPATIBLE WITH SPEEDUP DEVICES
The operation of the SpeedUp devices is guaranteed for the software versions of the ebikes released up to the date of purchase of the device itself.
If the ebike is subsequently updated with software for which the SpeedUp device has not been tested, it may fail to work and SpeedUp does not respond with the guarantee.
Before updating your engine it is necessary to check the compatibility with your SpeedUp device.

NB: All the brands mentioned on this site are named exclusively to identify the models of engines and bicycles on which our devices are compatible. They are the property of the respective owners and are in no way related to our company.

Use your helmet, save your life!

Contact